Insulation in Garland, TX
Crawl space encapsulation and vapor barrier work in Garland almost always means dealing with a vented dirt-floor crawl that has been absorbing Texas humidity since the Johnson administration. We routinely pull 40-year-old fiberglass batts out of Garland crawl spaces that have slumped, molded, or become rodent bedding, then seal the space and bring the thermal envelope up to something closer to 2026 standards. Garland’s late-1960s and 1970s tract ranch houses are the sweet spot for this work: slab-on-grade or short crawl, vented attic, and original R-11 material that was never enough for a Dallas-area heat sink. Call (855) 657-3403 if you suspect your crawl space is part of the problem.
Why Garland Homes Are Different
Garland built out fast between 1955 and 1985, which means the city has one of the densest inventories of pre-energy-code tract homes in the DFW metroplex. Thousands of those are single-story brick ranch houses with vented attics, slab foundations, and original insulation that has settled to an effective R-value well below the R-38 minimum in current Texas energy codes. Summer attic temperatures here routinely pass 150°F inside the Dallas urban heat sink, so a 1972 ranch with compressed fiberglass batts is fighting a losing battle every July afternoon. The February 2021 Winter Storm Uri exposed exactly how many of these older Garland homes were under-insulated: burst pipes and heating failures clustered in the neighborhoods we work most often.
There is also a Garland-specific defect we see constantly. Original bath and kitchen exhaust fans in 1960s and 1970s homes were often roughed in to vent directly into the attic rather than through the roof or a soffit. That means warm, moist air has been pumping into the attic insulation for decades, degrading batts, staining decking, and creating mold conditions before the insulation problem is even addressed. Any serious retrofit in Garland has to look at that venting issue at the same time as the insulation itself.
Our Main Garland Services
Garland homeowners call us most often for attic insulation retrofits and crawl space encapsulation, and both services are shaped by the city’s aging brick ranch housing stock. Here is the local landing page for the attic work; the full crawl space section follows below.
Attic Insulation in Garland
Garland’s pre-1985 ranch houses are the classic candidate for an attic insulation retrofit: original R-11 batts, vented attics, and no air sealing at the top plates. The job here typically means removing or topping up degraded fiberglass, sealing penetrations, and bringing the attic to R-38 or better. We see this work cut summer cooling bills noticeably for Garland homeowners, especially on the older central and east-side streets where the housing stock is densest. Attic Insulation in Garland covers the full process, including specific pricing for the city’s ranch and early-tract inventory.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Crawl Space Encapsulation & Vapor Barrier in Garland
Crawl space encapsulation in Garland means closing off a vented dirt-floor space that has been pulling in North Texas humidity for decades, then keeping it dry with a continuous vapor barrier and conditioned air. We do this work across Garland’s slab-and-short-crawl ranch inventory, where the original fiberglass between floor joists has often sagged, molded, or been shredded by rodents. The fix is a sealed crawl, not another layer of fiberglass, and it usually comes with a noticeable change in indoor air quality and humidity control. This is one of the services we most often recommend before or alongside an Crawl Space Encapsulation & Vapor Barrier retrofit, because fixing the crawl resolves the moisture problem that degrades everything above it.
Crawl Space Vapor Barrier
Signs you need it
You can smell earth or mildew in the house, especially after rain. Floor joists show dark staining, or you see standing water or visible damp soil under the house.
What it costs in Garland
Vapor barrier installation in Garland typically runs from $1,200 to $3,000 depending on crawl size and access.
How we do it
We clean out debris, level the dirt, and lay a continuous reinforced poly barrier across the floor and up the piers and walls. All seams are taped and mechanical fastening goes in where the soil is uneven.
Crawl Space Encapsulation
Signs you need it
Wood rot at the band joist, high indoor humidity that runs a dehumidifier constantly, or crawl vents that have never been closed are the classic signals.
What it costs in Garland
Full encapsulation in Garland typically ranges from $4,500 to $9,000 for an average ranch-house crawl.
How we do it
We seal the vents, insulate the band joist, cover the floor and walls with a continuous vapor barrier, and add a dehumidifier sized to the space. The crawl becomes part of the conditioned envelope instead of a damp air source.
Crawl Space Insulation
Signs you need it
Cold floors in winter over the crawl, or fiberglass batts drooping and touching the ground between joists.
What it costs in Garland
Crawl space insulation in Garland generally lands between $1,000 and $2,800 when done during an encapsulation.
How we do it
We remove the old, compressed material and replace it with closed-cell spray foam or rigid board at the band joist and foundation walls, leaving the floor joists open if the crawl is being conditioned.
What Crawl Space Encapsulation & Vapor Barrier Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Vapor barrier only (dirt crawl) | $1,200 - $3,000 |
| Full encapsulation with dehumidifier | $4,500 - $9,000 |
| Crawl space insulation (band joist & walls) | $1,000 - $2,800 |
| Rodent damage repair during encapsulation | $500 - $1,800 |
Is crawl space encapsulation worth it in Garland?
Yes, especially for pre-1985 Garland ranch homes built over vented dirt crawls. The humidity load here is significant, and sealing the crawl reduces indoor moisture problems and conditions the space under the house, which typically lowers the load on the HVAC system.
Can you replace the insulation while sealing the crawl?
We almost always do both in the same visit. The old fiberglass has absorbed moisture and rodent waste, so we remove it before sealing the vents and installing new material at the band joist and walls. Call (855) 657-3403 for a crawl assessment.
Spray Foam Insulation in Garland
Spray foam in Garland is often the answer for that oven-hot attic or the garage room that never cools down. Garland’s older ranch houses were built with vented attics and thin roof decking that radiate heat into the conditioned space from May through September, and open-cell or closed-cell foam changes that equation directly. We use several benchmark products, including Spray Foam Insulation systems from Icynene and Demilec, and the difference in a 1970s Garland ranch is usually felt the first full summer after install.
Open-Cell Spray Foam
Signs you need it
Uneven upstairs temperatures, AC running nonstop in July, or visible light gaps around plumbing and electrical penetrations in the attic.
What it costs in Garland
Open-cell spray foam on a Garland attic roof deck typically runs $2.50 to $3.50 per board foot.
How we do it
We spray the underside of the roof deck to create an unvented attic, closing the thermal boundary at the roofline instead of the ceiling. This keeps the ductwork inside the conditioned space.
Closed-Cell Spray Foam
Signs you need it
Crawl spaces with structural moisture issues, or garage ceilings and rim joists where you need an air, vapor, and thermal barrier in one pass.
What it costs in Garland
Closed-cell spray foam in Garland generally runs $3.50 to $5.50 per board foot, depending on thickness and access.
How we do it
We apply a dense foam that acts as all three barriers, often at the band joist, crawl walls, or garage shared wall. The material also adds racking strength to the framing.
Rim Joist Spray Foam
Signs you need it
Drafty floors at the exterior walls, or a crawl where you can see daylight at the band joist.
What it costs in Garland
Rim joist sealing with spray foam in Garland typically runs $800 to $2,200 for a full perimeter.
How we do it
We clean the band joist area and spray a continuous bead of closed-cell foam around the entire perimeter, sealing air leaks and insulating the band in one pass.
What Spray Foam Insulation Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Open-cell attic roof deck | $2.50 - $3.50 per board foot |
| Closed-cell crawl or garage | $3.50 - $5.50 per board foot |
| Rim joist sealing (full perimeter) | $800 - $2,200 |
| Garage ceiling spray foam | $1,800 - $4,200 |
Is spray foam safe in Garland heat?
Yes. Closed-cell foam performs well in Garland’s roof-deck temperatures and does not off-gas once cured. We ventilate during application and follow manufacturer re-entry times, and the installers are trained and background-checked.
Will spray foam fix a hot garage in Garland?
In most cases the garage ceiling is the biggest heat transfer point. Sealing and insulating it with foam reduces both radiant and conducted heat into the room above. Call (855) 657-3403 for a garage assessment.
Blown-In Insulation in Garland
Blown-in insulation is the fastest, least disruptive retrofit for Garland’s older ranch attics, where original R-11 batts have settled under decades of Texas roof-deck heat. We typically top up existing fiberglass with Blown-In Insulation made from GreenFiber cellulose or Owens Corning fiberglass, bringing the attic to R-38 or higher in a single visit. Most Garland jobs are done in one visit, and the material settles into the exact shape of the attic, which matters on older homes with irregular joist bays and shallow cavities.
Blown-In Cellulose
Signs you need it
High July cooling bills, attic thermometers reading 140°F+, or original 1960s batts that are flat and compressed.
What it costs in Garland
Blown-in cellulose in a Garland attic typically runs $1.20 to $1.80 per square foot.
How we do it
We prep the attic, blow GreenFiber or similar cellulose with a dense-pack machine to the specified depth, and verify the final R-value with a depth gauge.
Blown-In Fiberglass
Signs you need it
Water damage from a past roof leak, or rodent activity that has contaminated the original insulation.
What it costs in Garland
Blown-in fiberglass in Garland typically runs $1.00 to $1.50 per square foot for an attic top-up.
How we do it
We remove anything contaminated, then blow Johns Manville or Owens Corning fiberglass to the depth required for R-38 or better. The material is fire-resistant and does not hold moisture the way degraded batts do.
Dense-Pack Wall Insulation
Signs you need it
Walls that are cold in winter, exterior outlets that draft, or a 1970s Garland ranch that was built with minimal or no wall-cavity insulation.
What it costs in Garland
Dense-pack wall insulation in Garland runs $2.00 to $3.50 per square foot of wall area.
How we do it
We drill access holes from the exterior or interior, blow cellulose into the wall cavities under pressure, and patch the holes cleanly. This is a standard retrofit for Garland’s pre-1985 brick veneer homes.
What Blown-In Insulation Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Blown-in fiberglass attic top-up | $1.00 - $1.50 per sq ft |
| Blown-in cellulose attic | $1.20 - $1.80 per sq ft |
| Dense-pack walls | $2.00 - $3.50 per sq ft of wall |
| Attic removal + blow-in replacement | $2.50 - $4.00 per sq ft |
How long does blow-in last in Garland attics?
Cellulose and fiberglass both hold their R-value for decades unless there is roof leakage or rodent damage. The bigger issue in Garland is settlement over the first year, which is why we always install to a depth that accounts for it.
Can you blow insulation over old batts in Garland?
Usually yes, if the old material is dry and uncontaminated. If the original fiberglass has molded or been chewed through, we remove it first, then blow in fresh material. Call (855) 657-3403 for a straightforward attic check.
Radiant Barrier Installation in Garland
Radiant barrier is one of the few retrofits that directly addresses that July afternoon when your attic hits 150°F and the AC can barely hold 78 inside. Garland’s single-story brick ranch houses have large roof planes and shallow attic ventilation, which makes a foil-faced Radiant Barrier Installation a real candidate for cutting cooling load. We install reflective foil on the underside of the roof deck, and the effect is most pronounced in those central and east Garland neighborhoods where the houses are older and the AC systems are original.
Attic Radiant Barrier
Signs you need it
Attic temperatures above 140°F at mid-afternoon, or AC bills that spike every August.
What it costs in Garland
Attic radiant barrier in Garland typically runs $1.50 to $2.50 per square foot installed.
How we do it
We staple a low-emissivity foil to the underside of the roof rafters, leaving the ridge and soffit vents open. The foil reflects radiant heat before it can soak into the attic floor insulation.
Radiant Barrier Foil
Signs you need it
A hot attic that is already insulated to R-38 but still transfers heat to the ductwork above the insulation.
What it costs in Garland
Foil-only radiant barrier in Garland runs $1.20 to $1.80 per square foot.
How we do it
We install a double-sided reflective foil at the rafter line, which cuts radiant transfer into the insulation layer and protects the ducts from direct heat gain.
Radiant Barrier Roof Deck
Signs you need it
Homes with low-slope roofs or attics that cannot be vented effectively, or a garage that shares wall space with the home.
What it costs in Garland
Roof-deck radiant barrier in Garland runs $2.00 to $3.00 per square foot when paired with spray foam.
How we do it
We apply the foil to the roof deck from the attic side, often before an open-cell foam lift, creating a reflective air gap that boosts the foam’s effective R-value in Garland’s heat.
What Radiant Barrier Installation Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Attic radiant barrier (rafter-mounted) | $1.50 - $2.50 per sq ft |
| Foil-only retrofit | $1.20 - $1.80 per sq ft |
| Roof-deck barrier with foam | $2.00 - $3.00 per sq ft |
| Radiant barrier + ventilation adjustment | $2.50 - $3.80 per sq ft |
Does radiant barrier work in Garland’s humid climate?
Yes, because the benefit is radiant heat reflection, not moisture control. Garland’s attic heat is driven by direct solar gain on the roof, and a foil barrier cuts that load before it reaches the insulation, regardless of outdoor humidity.
Can I install radiant barrier with existing insulation?
Yes, that is the standard retrofit. The foil goes at the rafter line while the floor insulation stays in place. Call (855) 657-3403 if you want the attic measured for both.
Insulation Removal & Replacement in Garland
Removal and replacement in Garland is almost always triggered by one of three things: roof leaks that soaked the original 1960s or 1970s fiberglass, rodents that have nested and defecated throughout the attic, or the vented bath and kitchen fans that have been dumping moisture into the batts for 40 years. We remove the contaminated or degraded material, sanitize the attic, and re-insulate with Insulation Removal & Replacement products from Owens Corning, Johns Manville, or GreenFiber. Most Garland homes we service are single-story, so the removal is straightforward, but the moisture issue has to be addressed at the same time or the problem returns.
Attic Insulation Removal
Signs you need it
Visible mold stains on decking, insulation that is damp or crushed, or squirrel and rat droppings throughout the attic.
What it costs in Garland
Attic insulation removal in Garland typically runs $1.50 to $2.50 per square foot.
How we do it
We use a commercial vacuum to pull out the old material without spreading dust through the house, then inspect the decking and electrical for damage before any new insulation goes in.
Contaminated Insulation Removal
Signs you need it
Pest activity, a sewage or roof-leak event, or a musty smell that does not leave the attic.
What it costs in Garland
Contaminated insulation removal in Garland generally runs $2.00 to $3.50 per square foot, including sanitizing.
How we do it
We remove the material, fog the attic with an antimicrobial treatment, and seal the entry points before re-insulating. This is often paired with our attic rodent proofing work.
Vermiculite & Old Insulation Removal
Signs you need it
Homes built before 1990 (most of Garland’s central and east-side inventory) that still carry original loose-fill material, especially if it looks like small pebbles.
What it costs in Garland
Vermiculite removal in Garland typically runs $3.00 to $5.00 per square foot, and we treat it as potentially asbestos-containing.
How we do it
We do not disturb vermiculite unnecessarily. We remove it under controlled conditions with proper containment and disposal through a licensed waste stream, then test for asbestos before proceeding with replacement.
What Insulation Removal & Replacement Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Attic insulation removal only | $1.50 - $2.50 per sq ft |
| Contaminated removal + sanitizing | $2.00 - $3.50 per sq ft |
| Vermiculite removal | $3.00 - $5.00 per sq ft |
| Removal + blow-in replacement | $2.50 - $4.00 per sq ft |
Should I remove old insulation before adding new insulation in Garland?
If it is dry, uncontaminated, and not compressed beyond usefulness, no. If there has been roof leakage, rodent activity, or decades of moisture vented into the attic, yes. We inspect first and only remove what needs removing.
How long does a removal and replacement take in Garland?
A typical Garland ranch attic is one to two days for removal, sanitizing, and blowing in new material. Call (855) 657-3403 for a time estimate specific to your house.
Attic Air Sealing in Garland
Attic air sealing in Garland means closing the hundreds of small leaks that let conditioned air escape into a 150°F attic all summer. The older Garland homes have especially leaky top plates, unsealed can lights, and the notorious vented bath fans that were never ducted to the exterior, all of which pull air through the house and push cooling bills up. Sealing is done before or alongside Attic Air Sealing insulation upgrades, and it has to be done right or the new insulation underperforms.
Attic Floor Air Sealing
Signs you need it
Dust trails on the insulation, cold spots in the ceiling, or a slight draft at the top of interior walls.
What it costs in Garland
Attic floor air sealing in Garland typically runs $1,500 to $3,000 for a standard ranch attic.
How we do it
We pull back the existing insulation, seal all penetrations at the attic floor with foam and caulk, and re-cover the floor. This is best done before a blow-in upgrade, not after.
Top Plate & Penetration Sealing
Signs you need it
Visible gaps where interior walls meet the attic floor, or daylight showing around plumbing and wire chases.
What it costs in Garland
Top plate and penetration sealing in Garland runs $1,200 to $2,800, usually bundled with the floor sealing.
How we do it
We foam the top plates from the attic side where each interior wall meets the attic, then seal around all pipe and wire penetrations with fire-rated foam or caulk.
Can Light & Duct Boot Sealing
Signs you need it
Recessed lights that are warm to the touch, or ducts that feel drafty at the ceiling register.
What it costs in Garland
Can light and duct boot sealing in Garland runs $800 to $1,800 for a full attic.
How we do it
We seal around each recessed housing and duct boot with fire-rated material, installing covers where lights are not IC-rated. This is one of the highest-return air sealing jobs in older Garland homes.
What Attic Air Sealing Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Full attic floor sealing | $1,500 - $3,000 |
| Top plates and penetrations | $1,200 - $2,800 |
| Can lights and duct boots | $800 - $1,800 |
| Attic hatch sealing | $250 - $600 |
Is air sealing worth it before adding insulation in Garland?
Yes. Without air sealing, the new insulation still has conditioned air leaking through it into the attic. Sealing first means the insulation does the job it was rated for, and the cooling savings are larger.
How much air leaks from a Garland attic?
In a typical 1970s Garland ranch, the combined gaps at top plates, can lights, and duct boots can equal a permanently open window. Sealing those leaks is usually the first thing we do on a retrofit. Call (855) 657-3403 for an attic sealing estimate.
Wall Insulation in Garland
Wall insulation in Garland is the retrofit for those brick ranch houses that were built without any meaningful wall-cavity insulation, and the city has thousands of them. The brick veneer and siding were placed directly over framing with no exterior sheathing insulation, leaving the wall cavity empty or barely filled. Our standard fix for Garland’s older homes is Wall Insulation injected through small holes from the exterior or interior, using dense-pack cellulose or injection foam, depending on the cavity condition.
Injection Foam Wall Insulation
Signs you need it
Walls that feel cold in winter, or rooms that never hold a consistent temperature even after the attic is sealed.
What it costs in Garland
Injection foam wall insulation in Garland typically runs $4.00 to $6.00 per square foot of wall.
How we do it
We drill small holes at the top of the wall from the exterior, inject a slow-expanding foam that fills the cavity completely, and patch the holes in a way that disappears into the brick or siding.
Drill & Fill Wall Insulation
Signs you need it
Drafts through outlets, rooms above garages that never cool, or a pre-1985 house with no wall insulation at all.
What it costs in Garland
Drill-and-fill cellulose in Garland runs $2.50 to $4.00 per square foot of wall area.
How we do it
We drill from the outside, blow dense-packed cellulose into each cavity, and verify fill with a borescope. The holes are patched and matched to the existing finish.
Interior Wall Soundproofing
Signs you need it
Master bedrooms that share a wall with the garage or mechanical room, or street noise that comes straight through the front wall.
What it costs in Garland
Interior wall soundproofing in Garland runs $1.50 to $3.50 per square foot.
How we do it
We add sound-attenuating batt or injection foam to the wall cavity, and can combine it with acoustic sealant at the top and bottom plates for a much quieter room.
What Wall Insulation Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Injection foam full wall | $4.00 - $6.00 per sq ft |
| Drill-and-fill cellulose | $2.50 - $4.00 per sq ft |
| Interior soundproofing | $1.50 - $3.50 per sq ft |
| Garage shared-wall insulation | $1,800 - $4,000 |
Can you insulate the walls of a Garland brick house without replacing the brick?
Yes. Drill-and-fill from the exterior goes through the mortar joints or small holes in the siding, not through the brick itself. The brick face is never disturbed.
Do Garland homes have wall insulation?
Many pre-1985 Garland ranch houses have none or only a thin layer placed at original build. The wall cavities are usually empty, which is why drill-and-fill is such a common retrofit here. Call (855) 657-3403 for a wall cavity check.
Attic Cleaning & Rodent Proofing in Garland
Attic cleaning and rodent proofing in Garland often begins with the discovery that squirrels or rats have been nesting in the same 1974 fiberglass batts that were already underperforming. The city’s older housing stock gives rodents easy access through roofline gaps, and once they are in, they shred and contaminate the insulation. We remove the damaged material, sanitize the space, and close every entry point with Attic Cleaning & Rodent Proofing measures that keep them out.
Attic Cleanout
Signs you need it
Visible droppings, chewed wires, nesting material in the insulation, or a persistent animal noise from the ceiling.
What it costs in Garland
Attic cleanout in Garland typically runs $1,200 to $3,000, depending on the depth of contamination.
How we do it
We vacuum out the contaminated insulation, remove dead material and nests, and bag everything for disposal. The attic is then ready for sanitizing and re-insulation.
Attic Sanitizing & Decontamination
Signs you need it
Rodent urine odor that has soaked into the decking, or family members with allergy symptoms that worsen at home.
What it costs in Garland
Attic sanitizing in Garland runs $500 to $1,500, usually bundled with the cleanout.
How we do it
We fog the attic with an antimicrobial and odor-control treatment after the material is out, then apply a residual barrier to the decking and trusses before re-insulating.
Rodent Proofing & Exclusion
Signs you need it
Daylight visible at the roofline, chew marks around roof penetrations, or a cleanout that lasted less than a year before new signs appeared.
What it costs in Garland
Rodent exclusion on a Garland attic runs $1,500 to $4,000, depending on access points and roofline complexity.
How we do it
We seal every gap over a quarter-inch with galvanized steel mesh and foam, install chimney caps and vent covers, and trim back any tree branches that touch the roof.
What Attic Cleaning & Rodent Proofing Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Attic cleanout only | $1,200 - $3,000 |
| Sanitizing and decontamination | $500 - $1,500 |
| Rodent exclusion and proofing | $1,500 - $4,000 |
| Cleanout + exclusion + re-insulation | $4,000 - $9,000 |
Do I need to replace insulation after rodent activity in Garland?
Yes, in most cases. Rodent urine and droppings soak into the fiberglass and cannot be cleaned effectively. Removing and replacing is the only way to address both the contamination and the odor source.
How fast can you clean a rodent-infested attic in Garland?
A typical Garland attic is cleaned, sanitized, and sealed within one to two days. We schedule the re-insulation in the same visit whenever possible. Call (855) 657-3403 for urgent attic cleaning.
Serving Garland, TX - Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Home Energy Audit in Garland
A home energy audit in Garland is the diagnostic starting point that makes every other insulation decision smarter. Instead of guessing whether the attic or the walls are the problem, we measure it: blower door numbers, thermal images, and duct leakage all point to exactly where the 1960s or 1970s house is losing its conditioned air. A Home Energy Audit on a Garland ranch typically finds that the attic is the largest single source of loss, but the leaky top plates and unsealed ducts are often close behind.
Blower Door Test
Signs you need it
High energy bills with no obvious single cause, or a house that drafts even with windows sealed.
What it costs in Garland
A blower door test in Garland runs $200 to $500 when done alone, or is included with a full audit.
How we do it
We mount a calibrated fan in the front door, depressurize the house, and measure the total air leakage. That number becomes the baseline for every insulation decision we make.
Thermal Imaging Inspection
Signs you need it
Rooms that are always 5 degrees off from the rest of the house, or walls and ceilings that feel cold in one spot.
What it costs in Garland
A thermal imaging inspection in Garland runs $150 to $400, often bundled with the full audit.
How we do it
We scan walls, ceilings, and floors with a thermal camera while the house is under pressure, which makes insulation gaps and air leaks show up as clear cold or hot spots.
Insulation Inspection
Signs you need it
You do not know what is in the attic, or a home
Pricing for Insulation in Garland, TX
| Service | Typical range in Garland |
|---|---|
| Vapor barrier only (dirt crawl) | $1,200 - $3,000 |
| Full encapsulation with dehumidifier | $4,500 - $9,000 |
| Open-cell attic roof deck | $2.50 - $3.50 per board foot |
| Closed-cell crawl or garage | $3.50 - $5.50 per board foot |
| Blown-in fiberglass attic top-up | $1.00 - $1.50 per sq ft |
| Blown-in cellulose attic | $1.20 - $1.80 per sq ft |
| Attic radiant barrier (rafter-mounted) | $1.50 - $2.50 per sq ft |
| Attic insulation removal only | $1.50 - $2.50 per sq ft |
| Full attic floor sealing | $1,500 - $3,000 |
| Dense-pack walls | $2.00 - $3.50 per sq ft of wall |
Cost here depends on how easy the attic or crawl space is to access, how much depth is needed to reach code, whether old insulation has to be removed before new material goes in, and how large the space is. We put the final price in writing before work starts.
FAQs About Insulation in Garland, TX
How quickly can you schedule insulation work here?
We typically schedule an inspection within a few business days of your call, and most attic, crawl space, or wall jobs start within one to two weeks once we’ve confirmed the scope. Urgent issues, like an exposed attic or a failed vapor barrier, get priority scheduling.
Do I need a permit for insulation work in Garland?
Garland falls under Texas’s current energy code, which calls for R-38 in attics, well above what many of the city’s 1950s-1980s ranch homes were originally built with. Most standard insulation jobs don’t require a separate permit, but we size the work to today’s code minimums and handle any paperwork needed.
How does the written estimate process work?
We walk the attic, crawl space, or walls in person, measure the square footage, and note what condition the existing insulation is in. You get a written estimate with the recommended materials, R-values, and total price before any work begins, so there are no surprises once the crew arrives.
Which nearby areas do you cover?
We also regularly work in Houston, Spring, The Woodlands, Katy, Pearland, and Humble. If you’re just outside one of those areas, reach out and we’ll confirm whether your address falls within our current service radius.
What happens to my old insulation?
We remove and bag the old material, whether it’s compressed fiberglass, vermiculite, or insulation damaged by rodents, before installing anything new. Contaminated insulation gets disposed of according to local rules, and we sanitize the space so the new material goes into a clean attic or crawl space.
Frequently Asked Questions
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 60-minute.
- 4You approve before work beginsNothing starts until you say go.
What Garland Customers Say
"Radiant barrier stapled to the rafters plus new baffles at the soffits. Attic temperature dropped enough that the AC runs noticeably less in the afternoon. Crew was in and out in a day and left the garage cleaner than they found it."
- Sam Kessler"Injection foam in the walls of our 1950s house - no drywall demolition, just small holes patched and painted the same day. The street noise in the front bedroom is half what it was."
- Yasmin Farah"Upstairs was ten degrees hotter than downstairs every summer. They pulled the attic to bare joists, air-sealed every can light and top plate first, then blew it to R-49. First August in this house where the bedrooms and the living room read the same on the thermostat."
- Marcus Hale