Insulation in Sunrise, FL
Crawl space encapsulation and vapor barrier work in Sunrise typically runs $1,800 to $3,100 for a full system, and most homes here need it because western Broward County’s humidity creates persistent moisture problems that coastal cities don’t feel as acutely. Sunrise sits well inland, so the sea breeze that cools Fort Lauderdale never reaches your foundation, and homes built in the 1960s through 1980s often have bare-earth crawl spaces pulling damp air into the living space year-round. Call (855) 657-3403 for a free estimate, and a live person answers 24/7.
Why Sunrise Homes Are Different
Sunrise was built out fast as a master-planned community between the 1960s and 1980s, which left thousands of concrete-block (CBS) single-family homes and low-rise condos with attic assemblies that are the real thermal weakness, not the walls. In neighborhoods like Welleby and Sunrise Golf Village, many homes still carry original fiberglass batts rated R-11 to R-19, which falls far short of Florida’s current R-38 attic minimum. The attic is where Sunrise homes lose energy, and it’s where our crews spend most of their time.
But the climate is the bigger difference maker. Without Atlantic sea-breeze moderation, Sunrise attic temperatures routinely push past 150°F in summer, which cooks old insulation and forces AC systems to run longer. The May through October wet season then adds high indoor humidity that poorly detailed insulation systems can trap, creating mold risk. That’s why vapor management and ventilation are non-negotiable on every Sunrise job, not afterthoughts.
Decades of HVAC visits, pest-control trips, and storage shuffles have left many Sunrise attics with insulation that’s been walked on, shifted, or pulled back and inexpertly replaced. Low-pitch hip roofs, common throughout Welleby, make the problem worse because there’s less attic volume to work with and less forgiveness for sloppy installs. Full attic tear-outs and re-insulation jobs are more common in Sunrise than simple top-ups, and we plan for that reality from the first inspection.
Our Main Sunrise Services
Two services dominate the calls we take from Sunrise homeowners: attic insulation and crawl space work. Here’s what each one involves locally.
Attic Insulation in Sunrise
The typical Sunrise attic holds fiberglass batts that were barely adequate in 1985 and are now compressed, pest-disturbed, or outright gone in spots. Morning rooms run hot, upstairs bedrooms never cool evenly, and the AC seems to run without stopping. We inspect the full attic assembly, air-seal the floor, and bring the insulation up to current R-38 minimums with blown-in or batt material from Owens Corning or Johns Manville, then verify the work with a thermal camera. Most jobs finish in a single visit. See Attic Insulation in Sunrise for the full breakdown.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Crawl Space Encapsulation & Vapor Barrier in Sunrise
Crawl space encapsulation in Sunrise is a moisture-control job first and an insulation job second. The city’s inland location means summer humidity settles into the ground and rises through bare-earth crawl spaces, pushing damp, musty air into the home around every pipe penetration, rim joist, and floor seam. Homes in Sunrise built during the 1960s through 1980s boom were rarely fitted with vapor barriers or ground covers, so the problem is structural and widespread. We fix it by converting the crawl space into a dry, sealed, conditioned zone, and the full process is detailed on our Crawl Space Encapsulation & Vapor Barrier page.
The payoff for Sunrise homeowners is measurable: dry floors, no musty smell after rain, no rust on ductwork, and lower AC runtime because the house isn’t fighting ground moisture. Since most jobs are completed in a single visit and backed by the 90-Day Done Right Promise, it’s a clean fix for a problem that has often been misdiagnosed as a roof leak or plumbing issue.
Crawl Space Vapor Barrier
Signs you need it
You smell mildew when the AC kicks on after a rain, or you notice cupping hardwood floors and elevated indoor humidity readings even with the AC running hard. Squishy or damp soil under the house after a dry spell is another tell.
What it costs in Sunrise
Vapor barrier installation for a typical Sunrise crawl space runs $1,000 to $2,200 depending on square footage and access.
How we do it
We lay a reinforced poly liner across the entire crawl space floor, fasten it to the foundation walls, and seal all seams and penetrations to stop ground moisture from entering the home. The liner is mechanically attached, not just draped, so it survives future service visits.
Crawl Space Encapsulation
Signs you need it
Mold or mildew on the floor joists, insulation that feels damp to the touch, or a persistent musty odor that returns even after cleaning. Condensation dripping from ductwork in the crawl space in July is another strong signal.
What it costs in Sunrise
Full encapsulation for a Sunrise crawl space typically runs $2,200 to $3,100, with final cost driven by crawl space height, access points, and whether the rim joists need sealing.
How we do it
We dry the space, install the vapor barrier, insulate and seal the rim joists, and condition the crawl space with a dehumidifier so it becomes part of the home’s thermal envelope, not a wet cave underneath it. Every seam and penetration gets sealed before we finish.
What Crawl Space Encapsulation & Vapor Barrier Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Crawl space vapor barrier | $1,000 - $2,200 |
| Crawl space encapsulation | $2,200 - $3,100 |
| Crawl space insulation | $900 - $1,800 |
| Crawl space moisture control | $600 - $1,400 |
Is crawl space encapsulation worth it in Sunrise?
Yes, and the humidity math makes it a stronger investment here than in coastal cities. Sealing out ground moisture reduces AC load, prevents mold on framing and ductwork, and protects hardwood floors. Most Sunrise homeowners notice the air quality difference within the first week. Call (855) 657-3403 for an exact quote, free.
Can you handle a crawl space with standing water in Sunrise?
We handle it, but the water source has to be addressed first. If you have standing water, we inspect drainage and grade around the home before encapsulation so the vapor barrier doesn’t trap water inside the crawl space. Call (855) 657-3403 for a free assessment.
Spray Foam Insulation in Sunrise
Spray foam insulation in Sunrise does two jobs at once: it insulates and it air-seals, which makes it the most effective single product for the attic-roof assemblies in this city’s older CBS homes. Because Sunrise lacks the coastal breeze that moderates temperatures to the east, the roof deck absorbs direct sun all afternoon and radiates that heat straight down into the attic in summer. We apply open-cell or closed-cell foam to stop that heat transfer and eliminate the air leakage that lets humid outside air into the conditioned space. The full breakdown is on our Spray Foam Insulation page.
Spray foam also solves a problem specific to Sunrise’s low-pitch hip roofs, where there’s rarely enough attic volume for deep blown-in insulation. Foam delivers R-value per inch that fiberglass can’t match, and it adheres to the roofline so the attic can stay semi-conditioned without needing more depth. Most jobs are done in a single visit.
Open-Cell Spray Foam
Signs you need it
Rooms directly under the roof deck run consistently 8-10 degrees warmer than the rest of the house, or you see dust streaks and dark lines where air is pulling through can lights and ceiling penetrations.
What it costs in Sunrise
Open-cell spray foam in Sunrise runs $0.90 to $1.70 per board foot installed, with most attics landing between $2,200 and $4,500 total.
How we do it
We prep the attic, mask off non-target areas, and spray open-cell foam directly onto the roof deck or attic floor to create a continuous air and thermal barrier. The foam expands to fill gaps and cracks that batts can’t reach.
Closed-Cell Spray Foam
Signs you need it
You need a vapor barrier along with insulation in a damp-prone area like a crawl space or a rim joist, or you want maximum R-value per inch in a very tight attic cavity. Closed-cell foam also adds structural rigidity.
What it costs in Sunrise
Closed-cell spray foam in Sunrise runs $1.40 to $2.80 per board foot installed, making a typical rim joist job $900 to $1,900 and a full attic $4,000 to $8,000.
How we do it
We apply closed-cell foam in controlled lifts, usually 1 to 2 inches per pass, to the targeted surfaces. The higher density acts as both a thermal barrier and a Class II vapor retarder, which matters a lot in Sunrise’s humid crawl spaces.
What Spray Foam Insulation Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Open-cell spray foam | $0.90 - $1.70 per board foot |
| Closed-cell spray foam | $1.40 - $2.80 per board foot |
| Rim joist spray foam | $900 - $1,900 |
| Garage ceiling spray foam | $1,400 - $3,000 |
Is spray foam worth the extra cost in Sunrise?
For most Sunrise homes with 150°F summer attics, yes. The air-sealing benefit alone reduces AC runtime more than fiberglass can, and the R-value per inch is roughly double. The higher upfront cost typically pays back in 3-5 years here. Call (855) 657-3403 for a free estimate.
Can you spray foam an existing attic without removing old insulation?
Sometimes, but not always. If the old insulation is moldy, pest-soiled, or compressed, we remove it first so the foam can bond directly to the roof deck. We’ll tell you straight after the inspection. Call (855) 657-3403 to schedule one.
Blown-In Insulation in Sunrise
Blown-in insulation is the most common upgrade we perform in Sunrise because it’s the fastest, most cost-effective way to bring an under-insulated attic up to the R-38 standard this climate demands. The city’s 1960s through 1980s housing stock was built with R-11 to R-19 fiberglass batts, and those original batts have been compressed, shifted, and disrupted by decades of HVAC and pest-control traffic in the attic. Blown-in material fills the gaps batts leave behind and settles into the odd corners of low-pitch hip roofs that are everywhere in Welleby and Sunrise Golf Village. Details are on our Blown-In Insulation page.
For Sunrise specifically, we recommend blown-in fiberglass or cellulose based on the attic’s condition and whether the existing material can stay. Most jobs are completed in a single visit, and we air-seal the attic floor before blowing so the new insulation isn’t undermined by rising hot air.
Blown-In Fiberglass
Signs you need it
Your attic insulation measures below R-30, or you see bare spots, uneven coverage, and areas where the insulation has been pushed away from the eaves. Rising summer electric bills despite a healthy AC unit are another clue.
What it costs in Sunrise
Blown-in fiberglass in a typical Sunrise attic runs $1,400 to $3,100, depending on the target R-value and attic size.
How we do it
We air-seal the attic floor, then blow Owens Corning or Johns Manville fiberglass to a consistent depth that meets R-38 minimums. A thermal camera check confirms even coverage before we pack up.
Blown-In Cellulose
Signs you need it
Your existing attic has visible gaps, pest activity, or old insulation that’s settled below the joist tops. Cellulose also provides better sound deadening, which matters in Sunrise’s denser condo and townhome clusters.
What it costs in Sunrise
Blown-in cellulose for a Sunrise attic typically runs $1,500 to $3,300, with the final number set by the depth needed to hit R-38 and the attic’s footprint.
How we do it
We prep the attic, seal penetrations, and blow GreenFiber or similar cellulose to the specified depth with a dense, even coverage pattern. The material fills odd cavities in low-pitch roofs that batts always miss.
What Blown-In Insulation Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Blown-in fiberglass | $1,400 - $3,100 |
| Blown-in cellulose | $1,500 - $3,300 |
| Blown-in top-up | $800 - $1,600 |
| Dense-pack wall insulation | $2,000 - $3,800 |
How much does blown-in insulation save on AC bills in Sunrise?
Homeowners report 15-25% reductions in summer AC runtime after a proper air-seal and blown-in upgrade to R-38. The exact savings depend on the home’s worst leakage points, which is why we inspect first. Call (855) 657-3403 for a free estimate.
Can you blow insulation over existing batts in Sunrise?
Usually yes, if the existing batts are clean, dry, and not compressed below the joist tops. We’ll confirm during the inspection. If the old material is pest-soiled or moldy, removal comes first. Call (855) 657-3403 to schedule a look.
Radiant Barrier Installation in Sunrise
Radiant barrier installation in Sunrise attacks the city’s biggest insulation problem head-on: the radiant heat that turns attics into ovens because there’s no sea breeze to cool the roof deck. A radiant barrier is a reflective foil that blocks up to 97% of radiant heat transfer from the roof surface into the attic, which can lower attic temperatures by 20-30°F in the summer. For Sunrise’s 150°F attics, that’s the difference between an AC that cycles normally and one that never shuts off. See Radiant Barrier Installation for the full treatment.
Radiant barrier works best in cooling-dominated climates like ours, and Sunrise is a textbook case. We install it on the underside of the roof deck so the attic stays dramatically cooler, which protects stored items, extends roof life, and takes measurable load off the AC. Most jobs are completed in a single visit.
Attic Radiant Barrier
Signs you need it
Your attic is unbearable in summer, the AC struggles to hold setpoint on hot afternoons, or you can feel heat radiating through the ceiling below the attic. A simple touch test on the ceiling at noon tells the story.
What it costs in Sunrise
Attic radiant barrier installation in Sunrise runs $1,000 to $2,900 depending on the attic’s square footage and roof pitch.
How we do it
We staple a reflective foil to the underside of the roof rafters, creating a continuous radiant heat shield with proper air gaps above and below the foil. The installation is clean, fast, and doesn’t disturb existing insulation.
Radiant Barrier & Ventilation
Signs you need it
Your attic has poor airflow, with intake or exhaust vents blocked by insulation, and you want both a cooler attic and better moisture control. Radiant barrier alone won’t fix a ventilation problem, so we address both together.
What it costs in Sunrise
Radiant barrier combined with ventilation upgrades in Sunrise typically runs $1,800 to $4,200, covering the foil installation plus added intake or exhaust venting.
How we do it
We assess the existing ventilation, add or reposition vents where needed, then install the radiant barrier so heat is reflected out and what remains can escape naturally. This double fix handles Sunrise’s heat and humidity in one trip.
What Radiant Barrier Installation Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Attic radiant barrier | $1,000 - $2,900 |
| Radiant barrier foil | $800 - $2,000 |
| Radiant barrier roof deck | $1,200 - $3,200 |
| Radiant barrier & ventilation | $1,800 - $4,200 |
Does radiant barrier really help in Sunrise?
Yes, and Sunrise is one of the best places in Broward County for it. Without coastal breezes, your attic absorbs full sun all afternoon, and a radiant barrier cuts that radiant heat by up to 97%, dropping attic temps 20-30°F. Call (855) 657-3403 for a free estimate.
Can you install radiant barrier over existing insulation?
Yes, because the barrier mounts to the roof deck, not on top of the insulation. We leave existing attic floor insulation alone and work above it. Call (855) 657-3403 and a live person answers 24/7.
Insulation Removal & Replacement in Sunrise
We routinely pull out fiberglass batts from Sunrise attics that have been walked on, shifted, soaked by roof leaks, or soiled by rodents and then loose-laid back down by handymen. The low-pitch hip roofs common in Welleby make full tear-outs necessary because there’s no way to add material on top of a compacted, contaminated mess. The process is covered on our Insulation Removal & Replacement page.
After removal, we air-seal the attic floor and blow in fresh insulation to R-38 minimums, often using Knauf or Owens Corning material. The result is a clean thermal envelope that works, not a patchwork of old and new. Most jobs are completed in a single visit, and the 90-Day Done Right Promise applies.
Attic Insulation Removal
Signs you need it
Your attic insulation is compressed below the joist tops, visibly dirty, or full of debris from old roof work. You may also notice uneven room temperatures that never improve despite running the AC harder.
What it costs in Sunrise
Attic insulation removal for a typical Sunrise home runs $700 to $1,900, depending on attic size and accessibility.
How we do it
We use commercial HEPA-filtered vacuums to remove all old insulation down to the deck, bag it for disposal, and leave the attic clean and ready for inspection. The area is protected so dust doesn’t enter the living space.
Contaminated Insulation Removal
Signs you need it
You’ve had rodents, raccoons, or birds in the attic, or you see droppings, urine stains, and chewing damage in the insulation. Mold from a past roof leak is another reason to remove rather than cover over.
What it costs in Sunrise
Contaminated insulation removal in Sunrise runs $900 to $2,300 after sanitizing and disposal, with the range set by contamination level and attic size.
How we do it
We remove the contaminated material with HEPA filtration, sanitize the attic deck and framing, and then prepare the space for fresh insulation. Rodent-proofing can be added in the same visit.
What Insulation Removal & Replacement Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Attic insulation removal | $700 - $1,900 |
| Contaminated insulation removal | $900 - $2,300 |
| Complete removal & replacement | $2,500 - $5,500 |
| Vermiculite & old insulation removal | $1,100 - $2,700 |
How do I know if my Sunrise attic insulation needs full removal?
If the existing insulation is compressed below the joist tops, pest-soiled, moldy, or simply the original R-11 to R-19 from the 1970s or 80s, removal and replacement beats topping up. We’ll show you photos from the inspection. Call (855) 657-3403 to schedule one.
Can you remove and replace insulation in one day in Sunrise?
Most standard attic removals and replacements are finished in a single visit, usually one day. Larger attics or heavy contamination may need a second morning. Call (855) 657-3403 for a free estimate.
Attic Air Sealing in Sunrise
Attic air sealing in Sunrise stops the stack effect that pulls hot, humid outside air into the house through every crack, chase, and penetration in the attic floor. In a cooling-dominated climate like ours, air leakage through the attic is the single biggest driver of comfort problems: the AC cools the house, then that cooled air gets sucked out and replaced by 95°F humid air from the attic. Sunrise homes built in the 1960s through 1980s were never sealed to modern standards, so the leakage is built in. Full details are on our Attic Air Sealing page.
We seal before we insulate, every time. Sealing first means the new insulation works at its rated R-value instead of acting as a filter for moving air. For Sunrise specifically, we focus on the top plates, can lights, duct boots, and the attic hatch, which are the worst offenders in this era of home.
Attic Floor Air Sealing
Signs you need it
Rooms below the attic get stuffy and warm even with the AC running, or you notice dust streaks on insulation around penetrations, which show air moving through the attic floor.
What it costs in Sunrise
Attic floor air sealing in Sunrise runs $500 to $1,200 for a typical single-story attic, with the range set by the number of penetrations.
How we do it
We pull back the existing insulation at each penetration and seal around wiring, plumbing, and top plates with foam and caulk, then relay the insulation. The sealing is done before new insulation goes in.
Can Light & Duct Boot Sealing
Signs you need it
Your recessed can lights feel hot when you touch the trim, or you feel a draft around ceiling fixtures. Leaky duct boots also allow conditioned air to escape into the attic, which shows up as uneven room temperatures.
What it costs in Sunrise
Can light and duct boot sealing in Sunrise typically runs $300 to $900, covering the sealing of each fixture and boot that needs it.
How we do it
We use fire-rated covers or sealant appropriate to the fixture type to close the gap between the can light and the attic, and we seal each duct boot with mastic and foam. This one fix often makes the biggest immediate difference.
What Attic Air Sealing Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Attic floor air sealing | $500 - $1,200 |
| Top plate & penetration sealing | $400 - $1,000 |
| Can light & duct boot sealing | $300 - $900 |
| Attic hatch sealing | $150 - $400 |
How much does air sealing save in Sunrise?
Homeowners typically see 10-25% reductions in AC runtime after a complete attic air seal, because the house holds cooled air instead of leaking it into the attic. Savings are highest in Sunrise’s older CBS homes. Call (855) 657-3403 for a free estimate.
Do I need air sealing before new insulation in Sunrise?
Yes, without exception. Insulation does not stop air movement, and blowing new insulation over leaky penetrations just makes the leaks harder to reach later. Seal first, then insulate. Call (855) 657-3403 to schedule an inspection.
Wall Insulation in Sunrise
Wall insulation in Sunrise is a targeted fix, not a blanket solution, because this city’s CBS block homes rarely have empty stud cavities like wood-frame houses farther north. The blocks themselves provide some thermal mass, but uninsulated block walls still absorb heat all afternoon and radiate it inward after sunset. For Sunrise homeowners, wall work usually means injection foam into existing block cavities, drill-and-fill for furred-out drywall, or targeted exterior insulation on the hottest western exposures. See Wall Insulation for the complete rundown.
The wet-season humidity in Sunrise makes wall insulation choices matter more here than in dry climates. We avoid materials that trap moisture against block walls and use injection foam that air-seals as it insulates. Most wall jobs are completed in a single visit.
Injection Foam Wall Insulation
Signs you need it
Rooms on the west side of your Sunrise home heat up dramatically in late afternoon, and the walls feel warm to the touch from the inside. That’s radiant heat soaking through uninsulated block.
What it costs in Sunrise
Injection foam wall insulation for a typical Sunrise home runs $1,800 to $4,500, with the range set by the number of wall cavities and access points.
How we do it
We drill small access holes through the drywall from inside or through the stucco from outside, inject slow-rise foam that fills the cavity without over-expanding, then patch the holes. The foam air-seals and insulates in one step.
Drill & Fill Wall Insulation
Signs you need it
Your exterior walls feel empty, the home was built without any wall insulation, and heating or cooling only changes the air temperature without making the walls comfortable. Sound transfer through walls is another clue.
What it costs in Sunrise
Drill-and-fill wall insulation in Sunrise runs $1,600 to $4,000, driven by wall area, number of stories, and whether the job is done from inside or out.
How we do it
We drill into each stud bay, blow dense-pack cellulose or injection foam to fill the cavity completely, then plug and finish the holes. The dense pack prevents settling and stops air movement through the wall.
What Wall Insulation Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Injection foam wall insulation | $1,800 - $4,500 |
| Drill & fill wall insulation | $1,600 - $4,000 |
| Exterior wall insulation | $3,000 - $7,000 |
| Interior wall soundproofing | $1,200 - $3,200 |
Do CBS block homes in Sunrise need wall insulation?
Sometimes. The block provides thermal mass, but western exposures still soak up afternoon heat. If specific rooms run hot every afternoon, wall insulation on those walls solves it. Call (855) 657-3403 for a free assessment.
Can you insulate walls without tearing out drywall in Sunrise?
Yes, with injection foam or drill-and-fill. We work through small holes that get patched afterward, so there’s no full drywall demo. Most jobs are completed in a single visit. Call (855) 657-3403 for a free estimate.
Attic Cleaning & Rodent Proofing in Sunrise
Attic cleaning and rodent proofing in Sunrise is a necessary first step before any insulation work can hold up, because the city’s older housing stock has had decades of roof rats and squirrels finding their way in through gable vents, soffit gaps, and roof intersections. The damage isn’t just cosmetic: rodent activity compresses insulation, strips wire sheathing, and spreads droppings and urine through the attic, which then blows into the home as the AC moves air. Sunrise’s dense 1970s and 80s neighborhoods have the mature tree canopy and roof overhangs that rats need to access attics, making exclusion work a recurring request. The full scope is on our Attic Cleaning & Rodent Proofing page.
After we clean and sanitize, we seal the entry points so the problem doesn’t return, then the attic is ready for fresh insulation. Most jobs are completed in a single visit, and the 90-Day Done Right Promise applies to the exclusion work.
Attic Cleanout
Signs you need it
You see droppings, nesting material, or chewed insulation in the attic, or you hear scratching at night in the ceiling. The attic also may smell musty or ammonia-like, which indicates old rodent activity.
What it costs in Sunrise
Attic cleanout in Sunrise runs $400 to $1,100, with the range driven by attic size, the amount of debris, and whether disposal is needed off-site.
How we do it
We remove all debris, nesting material, and contaminated insulation with HEPA-filtered equipment, bag it for disposal, and leave the attic clean. This is always done before sanitizing or insulation replacement.
Rodent Proofing & Exclusion
Signs you need it
You’ve had rodents in the attic before and want to make sure they can’t come back. Look for gaps around plumbing vent pipes, loose soffit screens, and open gable vents, which are the typical entry points in Sunrise homes.
What it costs in Sunrise
Rodent proofing and exclusion in Sunrise runs $500 to $1,800, with the range set by the number of entry points, roofline complexity, and whether existing screens need replacement.
How we do it
We inspect every potential entry point, seal gaps with steel mesh and foam, replace damaged vent screens, and install one-way doors where needed. The goal is a closed attic that rodents can’t re-enter.
What Attic Cleaning & Rodent Proofing Costs in Sunrise
| Item | Typical range in Sunrise |
|---|---|
| Attic cleanout | $400 - $1,100 |
| Attic sanitizing & decontamination | $500 - $1,600 |
| Rodent proofing & exclusion | $500 - $1,800 |
| Attic restoration | $1,200 - $3,100 |
Do you handle rodent cleanup in Sunrise attics?
Yes, we handle the full sequence: removal of contaminated insulation, sanitizing, exclusion sealing, and restoration with fresh insulation. The entry points get sealed so the problem doesn’t repeat. Call (855) 657-3403 for a free estimate.
Can you clean my Sunrise attic without replacing the insulation?
Often yes, if the insulation is still in good shape. If it’s heavily soiled or compressed, replacement makes more sense than cleaning around it. We’ll show you what we find before any work begins. Call (855) 657-3403 to schedule.
Serving Sunrise, FL - Our Local Coverage Area
We’re based in the Sunrise area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Home Energy Audit in Sunrise
A home energy audit in Sunrise is the diagnostic starting point that makes every other insulation service smarter, because it measures exactly where your specific house is losing cooled air and pulling in humidity, rather than guessing. For Sunrise’s mix of 1960s through 1980s CBS homes and low-rise condos, the audit usually reveals attic leakage as the dominant problem, often combined with duct leakage that wastes 20-30% of the AC’s output. We run the tests, show you the numbers, and then you decide what to fix. Details are on our Home Energy Audit page.
The audit pays for itself by preventing the wrong fix. Many Sunrise homeowners assume they need new windows when the real problem is an unsealed attic or leaky ducts, and the audit proves it with measurements, not opinions. The $89 Seasonal Tune-Up and the 5% Senior & Veteran discount both apply to audit services.
Blower Door Test
Signs you need it
Your home feels drafty, rooms are never comfortable, and your energy bills stay high no matter what you do. The blower door test quantifies how leaky the house is and where the leaks are.
What it costs in Sunrise
A blower door test as part of a Sunrise home energy audit runs $200 to $450, with the full audit ranging from $300 to $600.
Pricing for Insulation in Sunrise, FL
| Service | Typical range in Sunrise |
|---|---|
| Crawl space vapor barrier | $1,000 - $2,200 |
| Crawl space encapsulation | $2,200 - $3,100 |
| Open-cell spray foam | $0.90 - $1.70 per board foot |
| Closed-cell spray foam | $1.40 - $2.80 per board foot |
| Blown-in fiberglass | $1,400 - $3,100 |
| Blown-in cellulose | $1,500 - $3,300 |
| Dense-pack wall insulation | $2,000 - $3,800 |
| Attic radiant barrier | $1,000 - $2,900 |
| Attic insulation removal | $700 - $1,900 |
| Attic floor air sealing | $500 - $1,200 |
In Sunrise, price depends on attic access, roof pitch, and how much old fiberglass batt has to be removed before new material goes in. Homes with contaminated or moisture-damaged insulation cost more due to the extra handling required. We put the full price in writing before any work begins.
FAQs About Insulation in Sunrise, FL
How quickly can we schedule an insulation job in Sunrise?
We typically schedule inspections and quotes within a few business days, and most installs finish in a single day depending on the size of the attic, crawl space, or walls involved. After you reach out, we confirm a visit window and send a technician to look at the space before writing up the work.
What insulation level does Florida code require in Sunrise?
Florida’s current attic minimum is R-38, but many older Sunrise homes in neighborhoods like Welleby and Sunrise Golf Village still carry original batts rated R-11 to R-19. We measure your existing insulation and compare it to that standard before recommending any upgrade.
How does the written estimate work?
We inspect the attic, walls, or crawl space in person, measure the area, and check the condition of any existing insulation before writing a fixed price. That estimate is given before any work starts, so the scope and total cost are set in advance with nothing added after the fact.
Which areas near Sunrise do we serve?
We regularly work in Houston, Spring, The Woodlands, Katy, Pearland, and Humble as well. If you’re not sure whether your address falls inside our coverage area, send us your zip code and we’ll confirm before scheduling a visit.
What happens to the old insulation when it’s replaced?
We remove and bag the old material before hauling it away for proper disposal, then clean the space if needed before installing anything new. If we find moisture damage, contamination, or pest activity in the old insulation, we’ll point it out and address it as part of the job.
Frequently Asked Questions
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 60-minute.
- 4You approve before work beginsNothing starts until you say go.
What Sunrise Customers Say
"Solid work on the spray foam in the rim joists and the garage ceiling. Scheduling slipped a day because of rain, which they called about ahead of time. Would use them again."
- Tom Reinholt"Crawl space smelled musty and the floors were cold. Full encapsulation with the thick liner taped at every seam, and a dehumidifier sized for the space. The hygrometer they left reads 48 percent now instead of the 70s."
- Elena Vasquez"The estimate had every line itemized - removal, sealing, baffles, the blown-in by the bag - and the final invoice matched it exactly. Two other companies quoted a single number and could not tell me what R-value they were installing."
- Priya Raman